Showing results: 361 - 375 of 523 items found.
-
HSM-I-08-08 -
Hall Research Inc.
The HSM-I-08-08 is a powerful 8x8 HDMI matrix switch with RS232 and IP control (internal web-server and Telnet). The unit supports HDCP, deep color, multi-channel digital audio (up to 7.1 channels), and may be used with any combination of DVI (PC) or HDMI (HDTV) sources and displays.
-
HA1600A -
Aim-TTi
Compliance quality measurements to EN61000-3-2 and EN61000-3-3Measures peak or rms voltage or current, real or apparent power, power factor, phase etc.Tabular/histogram of 40 harmonicsVoltage/current waveforms displaysContinuous analysis with real-time graphical updateWide range of power connectors available320 x 240 pixel high-contrast displayUSB, RS232 and printer interfaces fittedPC control and documentation software supplied (HA-PC-Link+)
-
61600 Series -
Chroma ATE Inc.
Built-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable voltage,current limitComprehensive measurement capability,V, Hz, Irms, Ipk, Iinrush, P, VAR, VA, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlOne-key recall for 9 different voltage and frequencyProgrammable slew rate setting for changing voltage and frequencyAnalog input for power amplifierOptional Analog programming interfaceOptional GPIB and RS-232 interface(Model 61601~61605)Full protection: OP,OC,OV and OT protectionEasy use graphic user interface: softpanel (option)Capable of delivering power output up tp 90KVA by implementing Master-Slave operation
-
ECP-100 -
Trans-Cal Industries, Inc.
The ECP-100 allows the avionics technician to assign serial port protocols, 100' or 10' resolution and/or allow programming of the calibration curve on Trans-Cal Altitude Encoders using the RS232 port.
-
9834 -
Interface Inc.
For use with amplified load cells and rotary torque sensors. Features 120 readings per second, programmable +/-10V or 4-20mA analog output, peak and valley monitoring, RS232. Packaged in an aluminum 1/8 DIN, panel mountable enclosure with a plug-in AC power cord. Sensor connection via 9-pin connector.
-
Model 4861B OEM -
ICS Electronics
* 114578-24 board has 4 isolated analog outputs, 4 isolated analog inputs, 4 isolated drivers and 8 digital inputs* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any ICS GPIB Connector/Address Switch Assembly.* Runs on 12 Vdc regulated power.
-
IFTOOLS GmbH
for analysis and optimizing of all RS232 and RS422/485 field-bus connections. It gathers exact information about every line change with 1µsec precision – indispensable for each analysis of time depending protocols like Modbus RTU, Profibus or similiar.
-
Series 90B -
Ametek Power Instruments
Dual independent communication ports (RS-232/485 and Ethernet) are available to transmit alarms to other devices. The Series 90B can receive alarms using communication ports, eliminating the need to connect digital inputs and associated wiring. The Series 90B supports Modbus, DNP and ASCII protocols.
-
Model 4804B-7 -
ICS Electronics
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Model 2399 -
ICS Electronics
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
0001-011 -
VI Control Systems Ltd.
A general purpose interface board for Mircromint's Answer Man Junior. Jumpers select one of three communication interfaces (RS-232, RS-485, or fiber optic RS-232). 12 bit ADCs and DACs are added for higher precision AD conversions. Answer Man Junior is included with the board.
-
ATC127 -
Vadatech Inc
The ATC127 is a high performance ATCA processor blade featuring dual 14-core Intel® Xeon® processor (E5-2658 v4, E5-2680 v4, E5-2648L, 2618L, 2620 or 2630 v4), with eight banks of memory up to 256 GB DDR4 memory. Versatile connectivity includes two PCIe Gen3 x16 Fabric Interfaces, dual GbE Base Interfaces, dual front panel GbE egress Ports, front panel dual RS-232 and USB 3.0/2.0 Ports and front panel DVI-I connector. Onboard mSATA storage is available for local boot.
-
ART108 -
Vadatech Inc
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
ART104 -
Vadatech Inc
The ART104 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC104 carrier board. The ART104 is a passive RTM that allows for Management 10/100Mbit Ethernet, Management RS-232 serial interface and PCIe x4 lanes for expansion.
-
ART103 -
Vadatech Inc
The ART103 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC103 carrier board. The ART103 is a passive RTM that allows for the additional connectivity of two GbE ports, Management 10/100Mbit Ethernet, Management RS-232 serial interface and three PCIe x4 lanes for expansion. One of the PMC J4s (user defined I/O) is routed to the back.